Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Sergej

Pages: [1]
1
Software / Programming of remote control
« on: 12.10.2005 at 14:03:48 »
How to program buttons on a remote control, using the terminal through a key {!}?
Keyboards in Yampp3/USB are not present?

The key enters into functions of management by the terminal {!} how to include Yampp3/USB in a mode of programming without use of keyboard Yampp3/USB, buttons of a remote control?

2
Hardware / Help me, MTD20P03HDL ?
« on: 10.10.2005 at 13:02:39 »
Hello Jesper!

It is possible to replace MTD20P03HDL on MTD20P06HDL?
I can not find in our shops this stabilizer.

3
Hardware / 33pF мы 27pF
« on: 30.09.2005 at 06:31:46 »
Hi, All!!
That will be if instead of condensers 33pF at assembly of the generator for Atmega162 and for VS1001k to establish 27pF?
As to me in shop have sold on 27pF
Whether will correctly work generators on these microcircuits?

4
Hardware / Help please Yampp3/USB
« on: 26.09.2005 at 07:06:34 »
I have Yampp3/USB chip USB FT8U245AM.
First the player worked perfectly but in a week when I have decided to collect it in the case, problems have begun...
When I have fastened IR have programmed buttons on the board all worked perfectly, then have transferred to the case and began....
First all is included perfectly, the song starts to play, press a player on the following song hangs!!!
Further I have decided to reprogram the program in the processor (ATmega161-8AI) all normally, is started BOOT all tests pass, when I tried to program firmware 1.30 program enters the name not from the first it is necessary to do this operation some times only then the program will be written down successfully, in result now test and bootloader I can not write down at all, YAAP speaks that a feed on the processor, but a feed on ATmega161-8AI is not sent is, after these operations for me does not work HDD (Toshiba MK4026GAX) What to do, prompt please?

Yours faithfully, Sergey.

5
Software / IR remote ?
« on: 16.09.2005 at 05:51:27 »
The problem how to define what standard supports IR? (Panasonic, REC80, etc.)

6
Software / Russian ID TAG
« on: 14.09.2005 at 06:09:13 »
Greetings, All!

Somebody added in the program support Russian ID TAG?
The program under Yampp3/USB with support Russian tag ` s on the indicator is necessary, share please.

Yours faithfully, Sergey.

7
General Board / Yampp3/usb+Sharp LM64CO8P-player DivX in car
« on: 04.08.2005 at 14:02:36 »
Player DIVX in the machine it is excellent!!!!

There is processor TMS320DSC24 hardware codec DivX who has any ideas?
And who else is engaged in this project?

8
Hardware / sharp LM64C08P
« on: 03.08.2005 at 12:37:27 »
Hi, All !!
Somebody can tried to connect TFT LCD to Yampp?
There are any offers on connection TFT, I have on a sign matrix sharp LM64C08P.

9
Hardware / Yampp-9
« on: 01.08.2005 at 12:24:36 »
Greetings Jasper!!!

When it will be laid out on site Yampp-9, in what stages of development?

10
Software / Id TAG
« on: 28.07.2005 at 06:50:17 »
Hi, All !!!
Somebody has program for Yampp3/USB supporting Russian ID TAG?

11
Hardware / HDD ST9145AG Help me!!!!!!!!!!!!
« on: 26.07.2005 at 06:25:02 »
HDD ST9145AG, the model is defined, and the size his zero MB in terminal Yampp,
It can 8 bit, old model?
In Yampp 16 bit trunk is applied?

Help me!!!!!!

12
Software / HDD format problem
« on: 21.07.2005 at 09:37:37 »
I have a problem.
When I connect yampp-3/usb with HDD (seagate ST9145AG - 128 Mb)
in terminal I see :

Hi, MP3 world!
yampp3/USB Alive
Firmware version:1.00 - Sep  1 2002 / 15:13:35
Disk Init... Ready!


And everything that does not occur
HDD it is not formatted


What to do ?


13
Hardware / Help, HDD it is not defined
« on: 21.07.2005 at 08:27:26 »
Greetings to all !!!!
Help, HDD it is not defined
The program in Yampp3/usb has written down versions 1.30
At start writes that the disk is present, the model seagate ST9145AG (for test) - is defined,
But the capacity writes 0 Mb, is exact also in the terminal,
All tests pass normally, but the ATA-test model HDD is defined ST9145AG capacity 0 Mb.
Help what to do?.

14
Hardware / Help to connect please LCD GDM1602S
« on: 01.07.2005 at 06:50:09 »
Hello, the help is necessary, it is necessary to connect LCD GDM1602S to Yampp3/u help, with the circuit of connection, beforehand many thanks.
The reference on  Datashits  www.hkfirms.com/worldtech/pdf/lcd-module/characterLCM/24.pdf

 

Pages: [1]